Waste Oil Furnaces and EPA Standards

Reznor Heater for Garage

You should keep in mind that when burning, waste oil has little odor or smoke, if you have a quality waste oil furnace. However, the best waste oil heaters will burn the oil cleanly and exceed EPA standards.

Maintaining waste oil heaters requires little effort. Remember that you’ll need to periodically clean out the residual ash and dust from inside the heater in order to maximize the efficiency of the unit. The filter needs to be washed or replaced occasionally.

Waste Oil vs. LP Gas

The energy potential of waste oil is much higher than that of regular LP gas. For instance, used motor oil has between 150,000-180,000 BTU per gallon and used vegetable oil has 128,000 BTU per gallon, while LP gas only has 92,000 BTU per gallon.

Reznor Heaters and Furnaces

Reznor is one of the most popular manufacturers of waste oil heaters and furnaces (read more about Reznor garage heaters). No doubt that these waste oil heaters have a huge financial and environmental benefit and should be seriously considered by a heat source by any home owner.

Reznor waste oil heaters can burn almost any used lubricants. The list of acceptable fuels to be burned includes transmission fluid, waste oils up to 50 weight, and #2 fuel oil.

The units of this famous brand are available in 4 sizes, ranging from 140000 btu’s to 500000 btu’s. Model RA and RAD unit heaters are CSA certified to UL Standards and meet EPA requirements for onsite recycling of used oils.

Here are some advantages of Reznor Waste Oil Heaters:

• Free heat.
• Limited liability on waste oil disposal.
• Elimination of disposal cost.
• Easier, cleaner and safer system for handling, storing and elimination of waste oils.
• If an approved and licensed transporter hauls your waste oil, you are still liable for any cleanup or removal action incurred.  Burning your oil on site eliminates your liability.
• Federal law states that the generator of used oil is responsible for the waste forever; however, if you burn it on site, your liability ends.
• When underground storage tanks with capacities of 1100 gallons or less are used for heating oil, they are exempted from the Federal UST Regulations.

Standard Features of Reznor Waste Oil Heaters:

•    Automatic, thermostat controlled operation
•    10-year combustion chamber / heat exchanger limited warranty
•    Remote pump system provides a metered flow of fuel
•    Oil preheating system (U.S. Patent No. 5,080,579)
•    Air atomizing burner
•    Built-in disconnect switches (pump and heater)
•    Permanently lubricated fan or blower motor with internal overload protection
•    Operation hour meter
•    24-volt thermostat
•    Barometric draft regulator
•    Electric spark ignition with electronic cad-cell flame safety system
•    Piston air compressor with replaceable filter
•    Fan and limit controls
•    High temperature limit control
•    Terminal block wiring
•    Flexible fuel line and built-in tray for service to the burner and nozzle (without disconnecting the fuel line)
•    Backflow sensor – CSA certified models
•    Large, easily accessible service panels designed to facilitate combustion chamber/ heat exchanger maintenance
•    Observation and overfire draft sampling ports
•    Supply line filter system with a disposable strainer and dirty filter indicator gauge
•    Individually adjustable horizontal louvers
•    Full safety fan guard or blower inlet and belt guards
•    Baked-on enamel finish
•    4-point threaded hanger connectors – Optional Features – Factory Installed
•    High altitude operation – Optional Features – Field Installed
•    Vertical louvers (Sizes 140, 235, and 350)
•    High altitude conversion kits (Sizes 235 and 350)
•    250-gallon workbench oil tank with or without heater stand (stand available for RA 140 and 235 only)
•    Hanger kit

Armstrong garage heaters may certainly match your home and garage requirements for coziness. In gentler weather conditions, Armstrong 2-stage furnace diminishes its production and on many days the furnace operates 75 – 80 % of the time on low-level production. This enables the furnace to run not frequently and produces a steadier and cozier atmosphere. When temperatures fall, the furnace functions at a 100 % competence and keeps your place pleasantly humid. This will let you work on your vehicle clean-up or your house upgrading project.

Armstrong Furnaces

Armstrong Garage Heaters

Armstrong furnaces employ incessant fan that provides regular temperature at the same time constantly filtering the air. Armstrong System Sentry control system facilitates in ensuring professional and safe process by continuously watching and controlling the heater. If there is a problem, the System Sentry will immediately offer service codes to a service provider to aid speedily and precisely identify the cause the trouble.

Heating systems have weathered heat exchanger made of stainless steel. It will supply you many years of dependable, worry-free performance. Armstrong furnaces with entirely shielded cabinet offer gentle, quiet process in all weather conditions. Armstrong has a 95 percent AFUE that is considered as one of the best efficiency evaluation presented on a gas furnace, drastically lessening heating overheads. Its motor with adjustable speed reduces your electric expenditure. These give one of the most energy-economical comfort schemes accessible this day.

Armstrong’s options for fin material, pitch, height and type help explain why heating cores last much longer and perform with greater efficiency than competitive units. These factors all have a bearing on heat transfer. Knowing how to balance these and other factors is the key to a cost-effective solution.

Types of Armstrong Unit Heaters

There are 2 fin types that are typically used in the manufacture of unit heaters. The L fin has a foot at its base and is tension-wound on knurled tube material. The L-shaped base provides a large contact area between the tube and the fin, ensuring effective, long-lasting heat transfer. The L fin is usually recommended when tubes and fins are of the same material.

The keyfin is manufactured by forming a helical groove in the tube surface, then winding the fin into the groove. The displaced metal from the groove is then peened against the fin. A tight fits between the fin and the tube. The keyfin is the superior design for dissimilar tube and fin material.

It’s very important to underline that basic units may be used in either horizontal or 2-way vertical-discharge configurations. The addition or substitution of a 4-way vertical louver section produces a square discharge pattern. Cores are available for steam or liquid, allowing units to be applied in different plant areas where various heating mediums may exist.

Enerco Garage Heater

Enerco offers many units of premium quality for its customers. For instance, this leading manufacturer makes portable radiant heaters with various models for propane and natural gas.

With heaters ranging from 35,000 to 125,000 BTU’s, Enerco provides heating solutions for a variety of applications such as construction sites, workshops, agricultural buildings, repair shops, remodeling jobs, loading docks, sporting events and more.

Enerco Garage Heaters.

Enerco Mr. Heater produces garage heaters. Infrared gas heater can perfectly suit for your garage.

Two models are the most popular. Model H25 will heat 500-600 sq ft a 2 1/2 car garage and Model H40 will heat up to 750 sq ft a 3+ car garage.

Enerco Infrared Garage Heater.

Infrared heat works like the sun. Objects are heated, then the heat radiates into the air. When the Enerco garage heater is first installed, it heats floor, car, the tools etc. Heat rises from the floor and all the objects to heat the air. Unlike forced air heaters that heat the air and then try to heat the objects. With infrared heater you can open the garage door and the heat stays in! With force air you lose all the heat every time the garage door is opened.

Infrared garage heaters require no electricity. They are intended to run 24-7. Once the floor and objects are heated to the temperature you set the unit will kick on a few times a day to keep everything warm. If you compare these heaters with forced air heaters, you’ll find out that they can kick on a few times per hour and need electricity to operate and no moving parts to maintain. No doubt that infrared heaters are most economical to operate.

Enerco infrared garage heaters aren’t just for garages. They can also be used in workshops, kennels, commercial buildings, shops, docks, driving ranges, patios and anywhere you need heat.

The Mr. Heater 42,000 BTU Propane Tank-Top Radiant Heater #F273900

Mr. Heater Garage Heater

This infrared garage heater mounts to a propane tank and supplies from 8000 to 42,000 BTUs with the triple burners. You can get up to 10 hours on a 20 pound cylinder. It’s very important to underline that if you are going to use it in your garage, then you should make sure there is plenty of ventilation so that the air keeps circulating with the fresh air outside. See also Mr. Heater natural gas heaters for garages.

The Mr. Heater 42,000 BTU Propane Tank-Top Radiant Heater #F273900

This infrared garage heater mounts to a propane tank and supplies from 8000 to 42,000 BTUs with the triple burners. You can get up to 10 hours on a 20 pound cylinder. If you are going to use it in your garage, make sure there is plenty of ventilation so that the air keeps circulating with the fresh air outside.

Mr. Heater 40, 000 BTU Propane Garage Heater

Here is good news for you. The Mr. Heater 40,000 BTU Propane Garage Heater is a highly efficient and cost effective radiant garage heater. In addition, its quiet, clean, odor free operation directly heats people and objects which in turn heat surrounding air to the desired temperature.

Heater is thermostatically controlled and requires no electricity to operate. There are no moving parts so maintenance is kept to an absolute minimum.

This CSA certified heater will heat up to 850 square feet and comes with a limited one year warranty on the controls and a pro-rated five year warranty on the burner assembly.

Mr. Heater Big Maxx 45,000 BTU Propane Garage Unit Heater

This quiet, vented can be a perfect choice for residential and commercial use. It can easily heat 2- to 3-car garage.

This heater requires only 1in. clearance from ceiling with 2 included angle brackets which means heater is up and out of the way.

The Mr. Heater Big Maxx 45,000 BTU Propane Garage Unit Heater is a propane fired, forced air convection heater. It’s very important to underline that this unit is ideal when ceiling heights do not allow for infrared heaters to be used.

In addition, this heater easily installs from the ceiling with included angle brackets. You should keep in mind that unit has power exhaust which allows for both vertical or horizontal venting.

Unit is thermostatically controlled and includes a spark ignition system with self diagnostic control module.

This is a CSA certified heater. It can heat up to 700 square feet. It comes with a 3 year limited warranty on the parts and the burner and a 10 year warranty on the heat exchanger.

Mr. Heater Big Maxx 75,000 BTU Propane Garage Unit Heater

This is a quiet, vented heater for residential and commercial use. This heater can also heat 2- to 3-car garage.

As the previous Mr. Heater, this heater also requires only 1in. clearance from ceiling with 2 included angle brackets which means heater is up and out of the way.

Power exhaust allows for vertical or horizontal venting. Low-profile cabinet measures 18in.W x 12in.D x 25in.H.

Unit is thermostatically controlled. It includes a spark ignition system with self diagnostic control module.

This CSA certified heater will heat up to 1,000 square feet.

Mr. Heater Vent Free Natural Gas Garage Heaters

Mr. Heater Garage Heaters

This type of Mr. Heater garage heater has a built in (factory installed) blower fan that distributes the heat around your garage or workshop. No venting or duct-work necessary. These units can operate without the fan during power outages.

For safety the flame is shielded behind a metal plate and a diamond mesh screen. This double layer of protection stops debris (including wood chips) from clogging up the gas outlet.

Mr. Heater Vent Free Natural Gas Garage Heaters also include a low oxygen depletion system (ODS). This option automatically shuts off the heater if the level of oxygen in the room even approaches an unsafe level for human occupation.

This type of heaters is easily mounted to the wall using the parts included in the box and comes with a built in battery powered ignition system (AA battery included in box).
The top mounted thermostat and easy to read digital temperature alone make this the best-in-class vent free garage heater.

Mr. Heater MH25NG 25,000-BTU Natural-Gas Radiant Heater

This heater is a quiet, odor-free, and low maintenance option. At 25,000 Btu, this unit is powerful enough to heat up to 500 square feet. It uses radiant heat. The heater comes fully assembled out of the box. You simply have to mount it and hook it up to your existing natural gas line. Do not use in inhabited or small, enclosed areas. AGA design certified. One-year warranty on gas control and five-year warranty on burner are included.

Mr. Heater Portable Buddy MRHF273400 LP Gas Heater

The Mr. Heater portable buddy is a small garage or shop heater. This is a perfect portable heater. Its weight is around 8 pounds. It has a handle that makes it convenient to carry even after it’s been used as it won’t be hot.

The heater can carry a 1 pound propane canister on the side of the heater which will help it to run for about 5 hours.

The temperature controls have 4 settings: off, pilot, low, or high. And on the highest setting it can heat about 200 square feet. It features a low oxygen shut off switch to help make it safe for indoor operation.

Nowadays Dayton produces different types of heaters for different uses:

Electric Dayton Heaters

Dayton Garage Heaters

Electric heaters are very popular heating options because they are much more inexpensive to purchase and much easier to maintain compared to other types of heaters. One of the great benefits of Dayton electric heater is the fact that it does not emit any harmful toxins or pollutants into your air. In addition, Dayton’s electric space heaters are all extremely effective when it comes to heating bedrooms or living rooms.

The U37 convection space heater can heat an area of 200 square feet. This unit is lightweight and sturdy. As convection heaters, Dayton’s U37, U33, and NW9 circulate air throughout the room to provide heat, keeping the entire room feeling nice and toasty for long periods of time.

The U31 electric space heater by Dayton relies on convection and radiant heating, which refers to the emission of infrared radiation that directly heats objects or people around the heating unit. You can choose whether you want to use the 2 heating methods separately or together.

Dayton also offers the oil-filled electric heater, the NX3. This heater features oil inside of the heater that is warmed, not burned. It’s very important to underline that because the oil is only warmed, no replacements are necessary. The NX3 heater provides a safe and efficient way of heating your room without harming the environment.

Dayton also offers several options for garages and small workshops. The D-F79 heater features heavy-duty heating that distributes air easily and quickly throughout the room. The Dayton D-F79 covers 17,000 BTUs of heating power.

No doubt that Dayton’s garage heaters are high-quality units that can effectively warm up large areas. The Dayton G73 garage heater can heat up to 500 square feet with its special features, such as its built-in thermostat and its 4 heat settings.

The Dayton L4000 and L5600 garage heaters feature 13,650 BTUs and 14,335 BTUs, respectively, and can keep your garage or workshop at any temperature between 45 and 95 degrees Fahrenheit. These lightweight and portable garage heaters also offer permanently lubricated motors and built-in thermostats for quick, effective warmth.

Gas-Fired Heaters

Gas-fired heaters use propane to provide heat. Dayton’s E46, E54, E55, E56, E57, and E58 are a perfect choice for providing warmth to warehouses, construction sites, factories, and open-air workshops. Dayton gas-fired heaters are convenient. With an efficient carrying handle, a gas-fire heater can be moved from one area to another with no hassle. These gas-fired heaters offer 50,000-150,000 BTUs of heat, which equals about 1,100-3,500 square feet of warmth. Dayton gas-fired heaters can give off up to 8 hours of heat with just one tank.

The TC25 and TC200VA liquid propane gas-fired heaters also feature 3 heat settings, flame safety systems, and matchless piezo ignitions, making the unit extremely safe in everyday use. These 2 heaters can cover 600 to 4,700 square feet.

Oil-Fired Heaters

Dayton offers many oil-fired heaters in its selection. An oil-fired heater relies on 1-K kerosene and uses no electricity at all. These units are great for heating up extremely large industrial areas. The E48, E49, E50, E51, and E52 oil-fired heaters all provide instant warmth and even feature easy to read fuel gauges and LED power/failure indicator lights for your convenience. These efficient heaters cover up to 45,000-210,000 BTUs of heat and can operate for an impressive 8-14 hours on one tank. The E50, E51, and E52 heaters come with a heavy-duty wheeled chassis kit that provides easy mobility.

Safety Features

All Dayton products offer safety features. The units have a tipover automatic safety feature that turns off the units if they fall over. In addition, the heaters offer a feature that turns off the units if they accidentally overheat. Moreover, in the case of overheating, the U31 and U33 units have an alarm that tells you when it is unsafe to keep your heater on for any longer. It’s very important to underline that the heaters than run on fuel also feature a “fuel shutoff” that turns the units off when the operation is getting too dangerous.

Remington brand is one of the most popular heaters in the market. No doubt that this brand is famous for its quality. Remington is the number one choice among the brands in the market today.

Types of Remington Garage Heaters

If you plan to purchase Remington heater, you may consider the fact that this type of heaters is available in many different varieties which are classified according to their style of functioning and the type of raw material which is used.

Remington garage heaters

Remington heaters which are quite popular are the Remington space heaters which feature self contained devices, portable in nature and used for heating an enclosed area. It’s very important to underline that Remington space heaters are not only safe but more efficient and economical as well since they radiate the heat uniformly into the surroundings and bring about a rapid rise in temperature. There are different varieties in which the Remington space heaters can be purchased are halogen space heaters, propane space heaters and electric heaters.
One of the benefits of Remington heaters is the fact that they are quite energy efficient and excellent for home usage. If you want to purchase Remington garage heater, you can easily shop them online.

Rem20NT Vent-Free Natural Gas Solar Fusion Garage Wall Heater

The Rem20NT Vent-Free Natural Gas Solar Fusion Garage Wall Heater is one of the most popular quality product of the brand Remington.

This heater can produce 10,500 – 20,000 Btu. Its easy controlled thermostat helps maintain the comfort level. It can heat up garages with up to 700 square feet area or a 20 x 35 foot room. It uses electronic ignition for easy lighting.

Moreover, Rem20NT doesn’t need electricity that makes it ideal for emergency heat applications. This heater can give variable heat output.

Rem20NT design is certified by the C.S.A. You should keep in mind that installation of this heater is very easy and does not require any expertise. It uses standard plumbing fittings.

The Rem20NT dimension is (H x W x D) 24.5” x 18.75” x 7.5”.

It’s very important to underline that burning comes very safe and clean. In addition, it is odorless, quiet, and clean. You should keep in mind that it can be used with natural gas only and cannot be converted to burn with other fuels.

The Modine Manufacturing Company which produces the Modine heater has been a leader in heating innovations and applications for many years. Thousands of heating systems of this brand are currently used in all kinds of automobiles that are used by everyone around the world. No doubt that in the modern world the Modine is a reliable brand of heating units.

Types of Modine Heaters

Modine Garage Heater

The Modine Company offers several models to choose from. Each model depending on the size of a room to be heated is designed to either for home use or for industrial use.

Before purchasing a Modine garage heater, you will need to consider the space you plan to heat while using your future heater. With the help of this heater, you can heat your garage more efficiently.
One of the most popular types of Modine garage heater is the Hot Dawg heating units. They feature the type of design that is most useful for heating up your garage or workshop.

It’s very important to underline that Hot Dawg garage heating units are one of the top sellers when it comes to heating a residential garage and workshops. You can be sure that you are making a powerful investment when you buy a customized garage heater. If you want something that will last you a good long time, then Modine garage heater is the best choice.

Nowadays you can choose to have your garage heater customized as a natural gas heater or a LP propane gas heater. You should choose the best type of heating power you need according to what is locally available to you. Some areas may already be serviced by natural gas or you may already be using propane as your main fuel source for the rest of  your property.

Installation of Modine Garage Heater

After purchasing a Modine garage heater you will need to take some measurements and determine where you will place your Modine garage heater. You should take into consideration clearance standards and local building codes before installing your garage-heating unit. You can install your own garage heater yourself. You may also call in a professional to install your heater for you.
Remember that a natural gas garage heater or a LP propane gas garage heater will need to be inspected when first installed. In addition, you will need to follow the directions of the manufacturer to ensure timely maintenance.
If you have determined where to install a Modine garage heater and have it inspected for safety, then you will enjoy the comfortable warmth it produces while you are working in your workshop or residential garage.

The term “vent free” means “unvented”. A vented gas heater or furnace requires a flue to rid the atmosphere of combustion by-products. A vent free heater emits those elements (primarily water vapor and carbon dioxide) directly into the space. In addition, a vent free heater is virtually 99.9% efficient.

There are many benefits of vent free heaters. One of them is that heaters of this type are safe. Vent free heaters have been used for 30 years to heat the dwelling spaces of homes in addition to residential garages and shops. You should keep in mind that vent free heaters must be properly sized for the space. For instance, a 2 car garage requires 20,000 – 30,000 BTU’s, depending on insulation, ceiling height and other factors.

Buy a vent free heater designated and approved as such. Most vent free heaters have refractory (catalytic) heating elements, which are able to burn fuel so efficiently that only traces of combustion by-products are left behind. Often a little extra humidity is beneficial, especially during the winter months when relative indoor humidity is low.

Remember that heaters that are not approved for vent free operation should never be left unvented. Forced air gas unit heaters, furnaces and radiant tube heaters fall into this category. They must be properly vented as per manufacturer’s requirements to prevent bodily harm or even death.

Vent free infrared heaters don’t require blower fans. They are whisper quiet.

Vent free heaters cost less to run than virtually any other type of gas heater. It’s great, isn’t it? That’s because all the heat energy goes into the space and nothing is wasted through an outside flue. In a well-insulated garage, the cost to operate a vent free infrared heater is very economic.

In addition, it is quite easy to install a vent free heater. Most vent free garage heaters don’t even require electrical power. A millivolt control mechanism turns the heater on when the thermostat calls for heat.

No doubt that vent free heaters are a perfect choice for the DIY homeowner. You just need to hang the heater, run the gas line and you’ve turned your garage into a year-round space for recreation, mechanics, exercise, animal comfort or to simply keep your vehicles warm on cold winter days.

Electric heaters are perfect choice for this project. They can be mounted anywhere, as long as power source exists. It’s very important to underline that they don’t need a ventilation unit – they can be used anywhere. You can fix the heater to the ceiling. It has many safety features integrated. When it overheats, it turns off.

Propane heaters are also great. But you should keep in mind that they need a vent to eliminate the gaseous emissions. They have a more complex system and they surely can’t be fixed by the ceiling.

If you decide on using a heater, no matter the type, you should see if there are any special regulations and if you need a special permit for that. You should obtain the permit if necessary.
If you plan to install a ceiling heater, you’ll need the following tools and materials:

· Tape measure

· Marking pen

· Number 14 nut driver

· Sammy wood screws

· Cordless drill

· 3/8-inch threaded rod

· 3/8-inch nuts

· 3/8-inch washers

· Hacksaw

· Pliers

· 9/16-inch ratchet wrench or 9/16-inch box wrench

· Safety glasses

Before installing the kit, you should read the manual to see if there are any special instructions for it.

Use the kit that came with the ceiling heater. Mount the brackets to the rafters on your garage ceiling. Use a power screwdriver to aid yourself.

Mount the unit.

First of all, you should turn off the power from your main electricity panel. Follow the instructions of the manufacturer. Some heaters come with a plug that can be plugged directly into an outlet.

Mount the thermostat on the wall, if the unit comes with such a device.

Turn on the electricity and then test the unit.

Check the circulation of the heat.